A double bass has a problem no violin shares. Standing it against a wall works until someone walks past it. Laying it on its side works until the bridge takes the weight. Every school with an orchestra reaches the same conclusion in the first term, which is that the instrument needs a stand of its own, and that the stand has to survive being knocked by a hundred teenagers a week.
Ours is the GS930, a folding A-frame with a padded cradle and a neck yoke. It is a simple piece of steel tube, and the design decisions in it are worth walking through, because a bass stand fails in ways a guitar stand never does.
A tall instrument on two small contact points
An upright bass is long, narrow and bottom heavy, and it rests on a stand at the base and at the neck. That second contact is where the leverage lives. A player bumping the fingerboard two hundred centimetres up translates into a real force at the feet, and any frame that only resists at the floor will walk across the room.
So the first question on any bass stand is not how much weight it carries. It is how far apart the contact points sit and whether the upper one actually captures the neck rather than just touching it. Our yoke is a padded U at the top of the post. The neck drops into it and cannot slide sideways without lifting the instrument, which is the behaviour you want in a room full of children.
The two lower arms do the carrying. They are set 55.5cm apart on our unit and lined with soft EVA foam, so the body sits on two padded rails rather than on the edge of a metal plate. Foam is not cosmetic here. A varnished bass body marked by a steel rail is a repair bill, and schools notice.

What an A frame does that a tripod cannot
The A frame is the older shape and the one most orchestras still ask for. Two splayed legs front and back, a vertical post, and a footprint that widens as it rises. The geometry means the load passes down the legs rather than into a single joint, which is why a folded steel A frame can be lighter than a tripod and still feel planted.
A tripod can work, but it concentrates stress at the hub where three legs meet, and that hub is usually a casting. Cast parts are fine until one arrives cracked after a season of being folded and thrown into a van. Tubular steel with welded or riveted joints is more forgiving of that treatment, and easier to inspect at the factory.
There is a practical difference too. An A frame stands on four feet, and ours rotate at the cap so the stand can be levelled on a stage that is not flat. A tripod on a raked stage or a gym floor tends to rock on one leg, and a bass that rocks is a bass that gets laid down instead.
Seventy five to a hundred and thirty centimetres of vertical range
Our post extends from 75cm to 130cm. That range exists because a quarter size bass and a full size bass differ by more than a metre in total height, and a stand sized for one will hold the other badly. The same unit covering both is what lets a school buy one model for a junior department and a senior department.
Check the locking collar, not just the range. A post that adjusts with a twist collar and a nylon sleeve holds its position under load. A post that relies on a pin through a hole gives you fixed steps and, on cheap units, a hole that ovalises after a year of use. Ours uses the collar arrangement, which also means the height can be set with the instrument already resting on the cradle rather than before.
Four cradle positions, and the sizes they serve
The cradle adjusts through four height positions, from quarter size to full size instruments. In practice the bottom two cover school instruments in a junior programme and the top two cover full size basses used by older players and by working musicians.
This is the setting a buyer should test with an actual instrument if possible. A cradle set too low leaves the body resting on the arms at a bad angle, which puts the bridge under load it was never designed for. Set correctly, the bass leans back into the cradle and its own weight does the holding.
The cradle is also detachable on our stand, and so is the neck yoke. That is what makes the folded package 79 by 9 by 16cm. Flat packed in a PE bag inside a brown carton, the whole thing weighs 3kg including the outer box, which is a courier friendly parcel rather than a freight item.
The hook is the detail most stands forget
A bow has to go somewhere while the bass is on the stand, and the answer on ours is a steel hook formed into the post below the yoke. It takes the bow by the stick, keeps it off the floor, and stops the player from laying the bow across the bass body where rosin dust does its slow damage.
This is a small thing that shows up in tenders. A school writing a specification for a music department will list a bow hook, because without one the bow ends up on a chair and the chair ends up on the bow. If a supplier's sample has no hook, ask whether it can be added, since it is a formed wire part rather than a redesign.

Folding is a school requirement, not a tour luxury
A stand that does not fold gets left assembled in a corner where it is in the way, and a stand in the way gets leaned on. Ours folds by releasing the cradle and collapsing the legs against the post, which takes a few seconds and no tools.
For a touring player the same feature is about van space. For a school it is about the storeroom, where eight stands have to live between rehearsals without becoming a pile of tangled tube. Buyers who have not sold into education tend to underrate this. It is often the reason a first order comes back for a second.
What ships beside a bass stand
Orchestral orders rarely stop at one frame. A department furnishing a string room will usually take cello and violin hardware in the same shipment, and consolidating saves one of the two inspection trips.
The cello stand covers the instrument one size down, and the solid wood cello endpin holder solves the floor question that comes with it. For smaller players the height adjustable ukulele and violin stand handles a junior section, and the guitar floor stand fills out the rest of the room.
All of these come out of the same Yinyu stands programme as the GS930, so a mixed orchestral order can be produced, packed and shipped as one lot rather than four.
How a bass stand order gets built
Ningbo Luxsound Technology has made instrument hardware in Ningbo since 2009, with a design team of ten and customers in more than sixty countries. Frame parts for the GS930 are formed and welded in house, and the foam and rubber components are produced to the same drawing as the rest of the Yinyu range.
OEM covers your logo on the post, your carton and your model code. ODM opens the frame geometry, the yoke shape and the height range, which is where a distributor serving a specific market tends to start.
Units are made against confirmed orders, so the quote you receive carries a production window and we confirm availability for your quantity when you ask. Terms can be DDP, with freight and duty included in the price you sign.
FAQ
What bass sizes does it take?
From quarter size to full size, with four cradle positions to match. The post extends from 75cm to 130cm to cover the same spread.
Does it hold a bass by the neck?
Yes. The padded yoke at the top captures the neck, and the two lower arms carry the body on EVA foam. The instrument leans into the cradle rather than balancing on it.
Is there somewhere to put the bow?
A steel hook is formed into the post below the yoke. It takes the bow by the stick and keeps it off the floor.
How flat does it pack?
The cradle and yoke detach and the legs fold against the post, giving a package of 79 by 9 by 16cm. Shipping weight including the outer carton is 3kg.
Can the feet be adjusted for an uneven floor?
The foot caps rotate so the stand can be levelled. That matters on raked stages and on gym floors, which are rarely flat.
Do you hold stock of this model?
It is built to order, so we quote a production window rather than a shelf quantity. Send the volume and the destination port and both come back on one quotation.
Measure the instrument, then send the quantity
Tell us the sizes your market actually stocks, whether the yoke needs your own branding, and the quantity for a first run. A drawing and a DDP quotation come back with those answers, and a sample can be in your hands before the order is confirmed.








